How To Install and Configure DKIM with Postfix on Debian Wheezy
The frustration of getting falsely flagged as a spammer is not strange to most of the mail server admins. By excluding the possibility of a compromised server, a false flag is usually caused by one of the following:
- the server is an open mail relay
- the sender's or server's IP address is blacklisted
- the server does not have a Fully Qualified Domain Name (FQDN) and a PTR record
- the Sender Policy Framework (SPF) DNS record is missing or it is misconfigured
- the DomainKeys Identified Mail (DKIM) implementation is missing or it's not properly set up
These are some of the basic properties that are being checked by the majority of proprietary and open source spam filters (including SpamAssassin). Passing these tests is extremely important for a well configured mail server.
This tutorial will focus on installing and configuring OpenDKIM]: an open source implementation of the DKIM sender authentication system.
It is assumed that the reader knows how to access the server over SSH, Postfix and Dovecot is already installed and configured (tutorial), the host name and the FQDN are set up (tutorial, tutorial) and the SPF record is in place (tutorial).
DKIM is an Internet Standard that enables a person or organisation to associate a domain name with an email message. This, in effect, serves as a method of claiming responsibility for a message. At its core, DKIM is powered by asymmetric cryptography. The sender's Mail Transfer Agent (MTA) signs every outgoing message with a private key. The recipient retrieves the public key from the sender's DNS records and verifies if the message body and some of the header fields were not altered since the message signing took place.
Before starting the installation, a system update is recommended:
sudo apt-get update sudo apt-get dist-upgrade
Install OpenDKIM and it's dependencies:
sudo apt-get install opendkim opendkim-tools
Additional packages will be listed as dependencies, type
yes and press
Enter to continue.
A couple of files must be created and edited in order to configure OpenDKIM.
Nano will be used as an editor because it's installed by default on DigitalOcean droplets and it's simple to operate:
- navigate with the arrow keys
- exit without saving changes: press
CTRL + Xand then
- exit and save changes: press
CTRL + Xand then
Y, and finally press
Important: replace every instance of example.com with your own domain in all commands and configuration files. Don't forget to save your files after editing.
Let's start with the main configuration file:
sudo nano /etc/opendkim.conf
Append the following lines to the end of the conf file (each parameter is explained below). Optionally, you can choose a custom port number for the
Socket. Make sure that it's not used by a different application.
AutoRestart Yes AutoRestartRate 10/1h UMask 002 Syslog yes SyslogSuccess Yes LogWhy Yes Canonicalization relaxed/simple ExternalIgnoreList refile:/etc/opendkim/TrustedHosts InternalHosts refile:/etc/opendkim/TrustedHosts KeyTable refile:/etc/opendkim/KeyTable SigningTable refile:/etc/opendkim/SigningTable Mode sv PidFile /var/run/opendkim/opendkim.pid SignatureAlgorithm rsa-sha256 UserID opendkim:opendkim Socket inet:12301@localhost
AutoRestart: auto restart the filter on failures
AutoRestartRate: specifies the filter's maximum restart rate, if restarts begin to happen faster than this rate, the filter will terminate;
10/1h- 10 restarts/hour are allowed at most
UMask: gives all access permissions to the user group defined by
UserIDand allows other users to read and execute files, in this case it will allow the creation and modification of a Pid file.
Syslog, SyslogSuccess, *LogWhy: these parameters enable detailed logging via calls to syslog
Canonicalization: defines the canonicalization methods used at message signing, the
simplemethod allows almost no modification while the
relaxedone tolerates minor changes such as
relaxed/simple- the message header will be processed with the
relaxedalgorithm and the body with the
ExternalIgnoreList: specifies the external hosts that can send mail through the server as one of the signing domains without credentials
InternalHosts: defines a list of internal hosts whose mail should not be verified but signed instead
KeyTable: maps key names to signing keys
SigningTable: lists the signatures to apply to a message based on the address found in the
Mode: declares operating modes; in this case the milter acts as a signer (
s) and a verifier (
PidFile: the path to the Pid file which contains the process identification number
SignatureAlgorithm: selects the signing algorithm to use when creating signatures
UserID: the opendkim process runs under this user and group
Socket: the milter will listen on the socket specified here, Posfix will send messages to opendkim for signing and verification through this socket;
12301@localhostdefines a TCP socket that listens on
This simple configuration is meant to allow message signing for one or more domains, to learn about other options please go here.
Connect the milter to Postfix:
sudo nano /etc/default/opendkim
Add the following line, edit the port number only if a custom one is used:
Configure postfix to use this milter:
sudo nano /etc/postfix/main.cf
Make sure that these two lines are present in the Postfix config file and are not commented out:
milter_protocol = 2 milter_default_action = accept
It is likely that a filter (SpamAssasin, Clamav etc.) is already used by Postfix; if the following parameters are present, just append the opendkim milter to them (milters are separated by a comma), the port number should be the same as in
smtpd_milters = unix:/spamass/spamass.sock, inet:localhost:12301 non_smtpd_milters = unix:/spamass/spamass.sock, inet:localhost:12301
If the parameters are missing, define them as follows:
smtpd_milters = inet:localhost:12301 non_smtpd_milters = inet:localhost:12301
Create a directory structure that will hold the trusted hosts, key tables, signing tables and crypto keys:
sudo mkdir /etc/opendkim sudo mkdir /etc/opendkim/keys
Specify trusted hosts:
sudo nano /etc/opendkim/TrustedHosts
We will use this file to define both
InternalHosts, messages originating from these hosts, domains and IP addresses will be trusted and signed.
Because our main configuration file declares
TrustedHosts as a regular expression file (
refile), we can use wildcard patters,
*.example.com means that messages coming from example.com's subdomains will be trusted too, not just the ones sent from the root domain.
Customize and add the following lines to the newly created file. Multiple domains can be specified, do not edit the first three lines:
127.0.0.1 localhost 192.168.0.1/24 *.example.com #*.example.net #*.example.org
Create a key table:
sudo nano /etc/opendkim/KeyTable
A key table contains each selector/domain pair and the path to their private key. Any alphanumeric string can be used as a selector, in this example
mail._domainkey.example.com example.com:mail:/etc/opendkim/keys/example.com/mail.private #mail._domainkey.example.net example.net:mail:/etc/opendkim/keys/example.net/mail.private #mail._domainkey.example.org example.org:mail:/etc/opendkim/keys/example.org/mail.private
Create a signing table:
sudo nano /etc/opendkim/SigningTable
This file is used for declaring the domains/email addresses and their selectors.
*@example.com mail._domainkey.example.com #*@example.net mail._domainkey.example.net #*@example.org mail._domainkey.example.org
Generate the public and private keys
Change to the keys directory:
Create a separate folder for the domain to hold the keys:
sudo mkdir example.com cd example.com
Generate the keys:
sudo opendkim-genkey -s mail -d example.com
-s specifies the selector and
-d the domain, this command will create two files,
mail.private is our private key and
mail.txt contains the public key.
Change the owner of the private key to
sudo chown opendkim:opendkim mail.private
Add the public key to the domain's DNS records
sudo nano -$ mail.txt
The public key is defined under the
p parameter. Do not use the example key below, it's only an illustration and will not work on your server.
mail._domainkey IN TXT "v=DKIM1; k=rsa; p=MIGfMA0GCSqGSIb3DQEBAQUAA4GNADCBiQKBgQC5N3lnvvrYgPCRSoqn+awTpE+iGYcKBPpo8HHbcFfCIIV10Hwo4PhCoGZSaKVHOjDm4yefKXhQjM7iKzEPuBatE7O47hAx1CJpNuIdLxhILSbEmbMxJrJAG0HZVn8z6EAoOHZNaPHmK2h4UUrjOG8zA5BHfzJf7tGwI+K619fFUwIDAQAB" ; ----- DKIM key mail for example.com
Copy that key and add a TXT record to your domain's DNS entries:
Name: mail._domainkey.example.com. Text: "v=DKIM1; k=rsa; p=MIGfMA0GCSqGSIb3DQEBAQUAA4GNADCBiQKBgQC5N3lnvvrYgPCRSoqn+awTpE+iGYcKBPpo8HHbcFfCIIV10Hwo4PhCoGZSaKVHOjDm4yefKXhQjM7iKzEPuBatE7O47hAx1CJpNuIdLxhILSbEmbMxJrJAG0HZVn8z6EAoOHZNaPHmK2h4UUrjOG8zA5BHfzJf7tGwI+K619fFUwIDAQAB"
Please note that the DNS changes may take a couple of hours to propagate.
Restart Postfix and OpenDKIM:
sudo service postfix restart sudo service opendkim restart
Congratulations! You have successfully configured DKIM for your mail server!
The configuration can be tested by sending an empty email to
email@example.com and a reply will be received. If everything works correctly you should see
DKIM check: pass under
Summary of Results.
========================================================== Summary of Results ========================================================== SPF check: pass DomainKeys check: neutral DKIM check: pass Sender-ID check: pass SpamAssassin check: ham
Alternatively, you can send a message to a Gmail address that you control, view the received email's headers in your Gmail inbox,
dkim=pass should be present in the
Authentication-Results header field.
Authentication-Results: mx.google.com; spf=pass (google.com: domain of firstname.lastname@example.org designates --- as permitted sender) email@example.com; dkim=pass firstname.lastname@example.org;