A question can only have one accepted answer. Are you sure you want to replace the current answer with this one?
You previously marked this answer as accepted. Are you sure you want to unaccept it?
I would like to have the following configuration
Laptop -> VPN1 -> VPN2 -> Internet
The software-properties-common package of the newest version (0.96.20.7) has already been installed. 0 was updated, 0 new packages were installed, 0 packages were deleted, and 1 package was not updated. Can not add PPA: 'ppa: ~ pritunl / ubuntu / ppa'. The team named '~ pritunl' has no PPA named 'ubuntu / ppa' Please choose from the following available PPAs:
For make used this [guide](http://https://www.digitalocean.com/community/tutorials/how-to-set-up-an-openvpn-server-on-ubuntu-16-04). I'm noob in linux, simple pls.
Hey, I've set up a Ubuntu 16.04 vps and fired up a Strongswan VPN. I managed to connect to the VPN with Windows client as well with my DVR with GSM modem. When I hit ipconfig on windows client amont others I get: PPP adapter DO VPN: Connection-specific DNS Suffix . : IPv4 Address. . . . . . . . . . . : 10.10.10.1 Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : 0.0.0.0 Also, when visitng whatismyip I get my VPSs IP address so routing is working fine. What I actually want to do is to have access to other clients on the VPN network. Is that at all possible cause I got confused? When I try to ping my windows client vpn address 10.10.10.1 from the server I get nothing: root@ubuntu-s-1vcpu-1gb-fra1-01:~# ping 10.10.10.1 PING 10.10.10.1 (10.10.10.1) 56(84) bytes of data. ^C --- 10.10.10.1 ping statistics --- 7 packets transmitted, 0 received, 100% packet loss, time 5999ms root@ubuntu-s-1vcpu-1gb-fra1-01:~# ifconfig eth0 Link encap:Ethernet HWaddr 1a:79:97:7b:98:f8 inet addr:159.89.10.55 Bcast:159.89.15.255 Mask:255.255.240.0 inet6 addr: fe80::1879:97ff:fe7b:98f8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7289 errors:0 dropped:0 overruns:0 frame:0 TX packets:7028 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2597792 (2.5 MB) TX bytes:2402868 (2.4 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:516 errors:0 dropped:0 overruns:0 frame:0 TX packets:516 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1 RX bytes:44023 (44.0 KB) TX bytes:44023 (44.0 KB) Is is something with configuration or maybe you have to connect server as a client as well? As you can see I am begginner here. Thanks a lot, V
We are running Ubuntu 16.04, clean install with latest StrongSWAN. We are creating a IPSEC tunnel between AWS and the droplet. The tunnel is up however we cannot connect to any ports on any AWS servers from the DO droplet. We verified no firewall rules on the AWS side and no firewall or ufw enabled on the DO side. This same scenario with AWS on one side and hardware VPN's on the other is working, it seems something specific to either the StrongSWAN config or DO infrastructure. Here is the VPN status: Security Associations (1 up, 0 connecting): Tunnel1[1]: ESTABLISHED 26 seconds ago, 162.243.5.4[162.243.5.4]...52.72.253.197[52.72.253.197] Tunnel1{1}: INSTALLED, TUNNEL, reqid 1, ESP in UDP SPIs: c849a6e6_i d4644947_o Tunnel1{1}: 0.0.0.0/0 === 0.0.0.0/0 VPN Config: config setup # strictcrlpolicy=yes uniqueids = no conn Tunnel1 auto=start left=%defaultroute leftid=162.243.5.4 right=52.72.253.197 type=tunnel leftauth=psk rightauth=psk keyexchange=ikev1 ike=aes128-sha1-modp1024 ikelifetime=8h esp=aes128-sha1-modp1024 lifetime=1h keyingtries=%forever leftsubnet=0.0.0.0/0 rightsubnet=0.0.0.0/0 dpddelay=10s dpdtimeout=30s dpdaction=restart mark=100 We have gone down so many paths to try to determine what is going on from the CIDR being too close to the DO Private IP to outdated StrongSWAN files. Any help is greatly appreciated. There must be something incredibly obvious we missed even though we have had 4 pairs of eyes on it for two days.